Power Supply Capacitors Repair Refurbish CARVER MXR-130 -150 THE RECEIVER Refurb

Description

Circuits and Concepts is n
ow offering upgraded replacement Power Supply capaci
tors to repair or refurbish classic
CARVER
THE RECEIVER,
MXR-130 and MXR-150 receivers.  These are pin-for-pin replacements for the large 42V and 63V electrolytic caps on the main (MA-508) board of the receiver.
Electrolytic capacitors, especially those made in the 1980's, age poorly.  They often fail as open circuits, where they lose capacitance which can cause hum, loss of clarity and "punch," and add distortion.  They can also become "leaky" and fail as short circuits.  This type of failure can cause pops, distortion and power supply failures, that can kill the audio signal entirely.
"Re-capping" a receiver is commonly done for the following reasons:
To repair an existing problem or failure in a receiver.
To restore or upgrade the audio quality of the receiver.
To reduce the possibility of future capacitor failures and improve the reliability of the receiver.
The kit contains 4 replacement electrolytic capacitors to replace the large, cylindrical 42 V and 63 V power supply filter capacitors on the main (MA-508) board.  The replacements for the 63 V capacitors include an adaptor board that allows the assembly to be inserted directly into the 3 pin footprint on the board--this is not available anywhere else!.  In addition, the capacitors' value is increased, which further lowers the noise floor and gives you added punch on the bass.  The parts are brand new and meet or exceed the specifications of the original parts.  To assure highest reliability, the capacitors in the kit are from a premier manufacturer with a high established component lifetime.
The kit includes:
Replacements for the two 42 V, 8,200 uF electrolytic capacitors on the MA-508 board.  Replacements are 10,000 uF, 50 V.
Replacements for the two 63 V, 10,000 uF electrolytic capacitors on the MA-508 board (with adaptor that allows you to solder the assembly directly into the board).  Replacements are 12,000 uF, 63 V.
A comprehensive installation and troubleshooting guide to aid in the repair and refurbishment of your receiver.
The installation manual gives detailed instructions with photos, showing how to replace the capacitors.  It includes a section on troubleshooting the power supply circuit, which is a common problem with the MXR receivers.  The troubleshooting guide is highly valuable and not available anywhere else.  The manual also shows how to clean the control potentiometers (v
olume, balance, tone, etc) and switches for continued, trouble-free operation.   The installation manual is a full-color PDF document delivered via e mail.
The listing is for a parts kit only, not the complete receiver.
Whether you are repairing a receiver for a specific problem, or doing a general update and refurbishmemt, this parts kit is ideal for getting that prized receiver in shape for the next decade or two of service!
Special Bonus!!!
With your purchase, we'll include a FREE, professionally scanned PDF copy of THE RECEIVER Service Manual  (the circuitry is virtually identical with THE RECEIVER, the MXR-130 & MXR-150).  The Service Manual includes schematics, block diagrams, parts lists and setup instructions.  Service Manual PDF will be delivered via e mail.
The parts can be replaced by a person with limited soldering skills.  A soldering iron, solder wick and solder are needed to replace the parts.  Use standard safety precautions (wear safety glasses, unplug the unit before soldering, good ventilation, etc) when working on your gear.  When you're done soldering, always wash your hands, because solder contains lead.  Please note that replacing components will fix the receiver only if those components was the problem to start with!
We offer the following parts for Carver receivers:
Tuner IC for intermittent or failed tuner sections
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220863094475&ssPageName=STRK:MESE:IT
Hard-to-find replacement knobs for Speaker Select, Tape Select and Tape Monitor
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220881903753&ssPageName=STRK:MESE:IT
Relays/trim cap/power supply resistor Refurbishment kit that contains the parts to address Carver Service Bulletins on Carver Receivers:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=320780840585
If you just want Output Relays
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=221121502953&ssPageName=STRK:MESE:IT
High Performance Voltage Regulator Assembly to replace the burnt-up-ugly-mess of resistors on the MXR-130 and -150 Noise Reduction Board:
https://www.ebay.com/itm/223894145374
23 Electrolytic Capacitor replacement kit for the MXR-130/-150 Power Supply/Amplifier board to fix power supply problems and improve audio quality:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=221255991499&ssPageName=STRK:MESE:IT
See our other listings for other interesting and helpful electronic solutions!  Shipping is discounted for multiple purchases!  Please send us a message if you have any questions.  We've worked with Carver equipment for nearly 30 years.  We love classic audio equipment, and want to help you get the most enjoyment out of your system!  We also repair Carver equipment at our location.  Let us know what you need!
Buyer to prepay with Paypal and pay .95 flat rate for shipping and professional packing (that means .95 per shipment regardless of the number of parts in the order--if e bay charges more, we promptly refund the excess charges).  Additional shipping cost outside the US.   Positive feedback will be left for successfully completed transaction.